If you are looking for the correct TRC Bologna frequency, you can receive the channel through a transmission available on Eutelsat 9B at 9.0° East. Unlike standard satellite frequencies, this transmission uses DVB-S2 with 16APSK Multistream technology, specifically Stream 17, which means that your satellite receiver must support Multistream reception.
TRC Bologna is an Italian television channel, and the listed transmission is available in HD using MPEG-4, with Italian audio.
In this guide, we explain the complete steps to add the TRC Bologna frequency manually, the correct satellite parameters, how to activate Multistream settings, and what to do if the receiver does not detect the channel.
TRC Bologna Frequency on Eutelsat 9B
The listed TRC Bologna transmission is available on Eutelsat 9B at 9.0° East.
The main parameters are:
- Satellite: Eutelsat 9B
- Orbital Position: 9.0°E
- Frequency: 12466 MHz
- Polarization: Vertical (V)
- Standard: DVB-S2
- Modulation: 16APSK
- Technology: Multistream
- Stream: 17
- Symbol Rate: 41950
- FEC: 2/3
- Service ID: 4802
- Video PID: 1110
- Video Format: MPEG-4 HD
- Audio PID: 1111
- Audio Language: Italian
For a quick manual search, the main transponder information is:
12466 V 41950
However, because this is a Multistream transmission, entering only the frequency, polarization, and symbol rate may not be enough. The receiver must also be configured correctly for 16APSK Multistream Stream 17.
How to Add TRC Bologna Manually
To add the channel, open the satellite installation menu on your receiver.
Depending on the receiver brand, this section may be called Installation, Satellite Search, Transponder Search, or Manual Scan.
Select:
Eutelsat 9B – 9.0°E
Then create a new transponder and enter:
Frequency: 12466 MHz
Polarization: Vertical (V)
Symbol Rate: 41950
FEC: 2/3
System: DVB-S2
Modulation: 16APSK
After entering the basic parameters, look for the receiver’s Multistream, MIS, or PLS/Stream settings.
Set the stream or input stream to:
Stream 17
Then start the transponder search.
If your receiver supports the required Multistream technology and your dish is correctly aligned with Eutelsat 9B, the receiver should be able to detect the services carried on this transmission.
Why Multistream Support Is Important
The TRC Bologna transmission is not a conventional DVB-S2 broadcast. It uses DVB-S2 16APSK Multistream, which requires a compatible receiver.
A receiver may allow you to enter 12466 V 41950 but still fail to find the channel if it does not support Multistream.
This is one of the most common reasons users may see no result after entering an apparently correct frequency.
Before changing the dish alignment, check whether your receiver supports:
- DVB-S2
- 16APSK
- Multistream / MIS
- Stream ID selection
Modern satellite receivers designed for Multistream reception can usually provide these settings in the advanced transponder search menu.
How to Set Stream 17
After entering the transponder parameters, open the advanced modulation or Multistream settings.
Depending on the receiver software, the option may appear under names such as:
MIS, Multistream, Input Stream ID, Stream ID, or ISI.
For the TRC Bologna transmission, use:
Stream ID / ISI: 17
Once Stream 17 is selected, save the settings and start the scan.
If the receiver has an option for automatic Multistream detection, you can also try enabling it. However, manually selecting Stream 17 can be more useful when the receiver does not automatically detect the service.
TRC Bologna Service ID and PIDs
Advanced satellite receivers may also display the service identification parameters.
The listed values are:
SID: 4802
Video PID: 1110
Audio PID: 1111
The video uses MPEG-4 HD, while the audio is in Italian.
Most modern receivers will obtain these values automatically after a successful transponder scan, so you normally do not need to enter the PIDs manually.
Manual PID entry is mainly useful for professional receivers or installations where automatic service detection is not working correctly.
What to Do If TRC Bologna Shows 0% Signal
If the signal level remains at zero, start with the satellite selection.
Make sure your dish is actually pointed toward:
Eutelsat 9B – 9.0°E
Selecting another satellite can result in incorrect or completely absent signal readings.
Also check the LNB connection, coaxial cable, connectors, and the receiver’s LNB configuration.
What If Signal Strength Is High but Signal Quality Is Low?
A high signal-strength percentage does not necessarily mean that the transponder is being received correctly.
The important indicator when tuning a satellite frequency is generally signal quality.
If strength is high but quality remains very low, the dish may be slightly misaligned or the receiver may be locked onto a different signal.
Make small adjustments to the dish and monitor the quality indicator rather than relying only on signal strength.
Check the Polarization
The correct polarization for TRC Bologna is:
Vertical (V)
Make sure the receiver is not set to Horizontal.
Incorrect polarization can prevent the receiver from locking onto the transponder even when the frequency and symbol rate are correct.
Check the Symbol Rate
The correct symbol rate is:
41950
Entering an incorrect symbol rate can cause the receiver to fail to lock onto the transmission.
Because this is a relatively high symbol rate, make sure the receiver accepts the value correctly and supports the required DVB-S2 transmission parameters.
Why Can’t My Old Receiver Find TRC Bologna?
The most likely reason is lack of Multistream and 16APSK support.
Older satellite receivers may support DVB-S2 but still lack support for the specific Multistream configuration used by this transmission.
If your receiver does not provide options such as MIS, ISI, Multistream, or Stream ID, it may not be suitable for receiving this service.
Upgrading to a receiver with DVB-S2 Multistream support may be necessary.
Is TRC Bologna Available in HD?
Yes. The listed transmission uses MPEG-4 HD for video.
The audio is listed in Italian, making the channel suitable for viewers looking for Italian-language television content.
Can I Use a Blind Scan?
A blind scan can be useful when you want to discover all available services on Eutelsat 9B.
However, for TRC Bologna, a manual scan is generally more efficient because the exact transponder parameters are already known.
Enter:
12466 V 41950
and configure the Multistream settings with:
Stream 17
Then perform the scan.
Manual Settings for TRC Bologna at a Glance
For quick reference, use the following settings when configuring the receiver:
Satellite: Eutelsat 9B 9.0°E
Frequency: 12466 MHz
Polarization: Vertical
System: DVB-S2
Modulation: 16APSK
Symbol Rate: 41950
FEC: 2/3
Multistream: Yes
Stream: 17
SID: 4802
Video: MPEG-4 HD
Video PID: 1110
Audio PID: 1111
Audio: Italian
Frequently Asked Questions
What is the TRC Bologna frequency?
The listed TRC Bologna frequency is 12466 MHz Vertical (V) on Eutelsat 9B at 9.0°E.
What is the symbol rate for TRC Bologna?
The symbol rate is 41950 with FEC 2/3.
Does TRC Bologna use Multistream?
Yes. The transmission uses DVB-S2 16APSK Multistream with Stream 17.
What satellite carries TRC Bologna?
The listed transmission is carried on Eutelsat 9B at 9.0° East.
Why can’t my receiver find TRC Bologna?
The most common reason is that the receiver does not support DVB-S2 16APSK Multistream or does not allow the correct Stream ID to be selected.
What is the Stream ID for TRC Bologna?
The listed Multistream value is Stream 17.
What is the SID of TRC Bologna?
The listed Service ID is 4802.
What language is TRC Bologna broadcast in?
The listed audio language is Italian.
Adding the TRC Bologna frequency requires slightly more than a normal satellite scan because the transmission uses DVB-S2 16APSK Multistream.
The key settings are 12466 MHz Vertical, symbol rate 41950, FEC 2/3, and Stream 17 on Eutelsat 9B at 9.0°E.
If your receiver supports Multistream, enter the transponder parameters manually and make sure the Stream ID is correctly set to 17. If the channel is still not detected, check the dish alignment, signal quality, LNB configuration, and receiver compatibility before changing other settings.
